LORA WIFI RF Arduino Shield, ESP8266 SX1278 - ElectroDragon
![LORA WIFI RF Arduino Shield, ESP8266 SX1278 - ElectroDragon](https://s5.electrodragon.com/wp-content/uploads/2018/02/ESP-LORA-WIFI-RF-Arduino-Shield-004-768x592.jpg)
This arduino shield combine the wifi mcu module esp-12f and lora sub-1G RF module. ESP8266 ESP-12F Features: ESP-12F serial to Arduino serial, selectable D0 / D1 or soft serial D2 / D3 All pins lead out, is not connected nor occupy by Arduino IO port ESP-12F can work as slave mode for arduino, or program […]
This arduino shield combine the wifi mcu module esp-12f and lora sub-1G RF module.
ESP8266 ESP-12F Features:
ESP-12F serial to Arduino serial, selectable D0 / D1 or soft serial D2 / D3
All pins lead out, is not connected nor occupy by Arduino IO port
ESP-12F can work as slave mode for arduino, or program independently.
ADC and ADC external voltage port lead out.
On board PROG programmable button, and ESP reset button.
Demo code inlcudes manipulating AT commands to transiceive data from web, find in the wiki documentaion link below.
Can be used independently, can be connected to a standard serial communication FTDI
Lora Module SX1278/76:
Reserved but not place module.
D10 default used for lora chip select pin.
D5-D7 can connect via jumper to D1, D2, D5 lora DIO pins.
D2 default used for lora IRQ DIO0 pin.
Antenna not connected default, support pin, ipex, or sma type connector, suit your needs.
All lead out DIO D0 ~ D5 pins on side.
Addon:
Extra DH11 socket, with 10K pull-up data pin.
Packaging:
Only include the main board with esp-12F as red board.
Not include any pin headers, lora module, antenna.
Arduino pin header please buy alone here.
the last image of the green board indicates the final soldered state only.
Documentation please see on this page.
![](https://how2electronics.com/wp-content/uploads/2020/02/SS-LoraSimple.png)
LoRa SX1278 & ESP8266 Transmitter Receiver with DHT11 Sensor
![](https://shop.makestro.com/wp-content/uploads/sites/2/2017/08/ESPectro32-Top-Side-fot-RIoT-1-1.jpg)
The Internet of Things with ESP32
![](http://esp32.net/images/LilyGO/X-32/WeMos-fake_X-32_PhotoCollage.jpg)
The Internet of Things with ESP32
![](https://ae01.alicdn.com/kf/HTB1tZQbzk9WBuNjSspeq6yz5VXaZ/2pcs-lot-Lora611PRO-915MHz-5Km-sx1276-sx1278-AES-encrypted-MESH-network-Smart-Repeater-Node-Wireless-Lora.jpg)
2pcs/lot Lora611PRO 915MHz 5Km sx1276/sx1278 AES encrypted MESH
![](https://how2electronics.com/wp-content/plugins/wp-youtube-lyte/lyteCache.php?origThumbUrl=https%3A%2F%2Fi.ytimg.com%2Fvi%2F0pSjLgWp1U8%2F0.jpg)
LoRa SX1278 & ESP8266 Transmitter Receiver with DHT11 Sensor
![](https://wiki1.dragino.com/images/thumb/e/e4/Lora_Shield_v1.4.jpg/400px-Lora_Shield_v1.4.jpg)
Lora Shield - Wiki for Dragino Project
The Relay shield is capable of controlling 2 relays. The max switching power could be 10A/250VAC or 10A/30VDC. It could be directly controlled by
![](https://s5.electrodragon.com/wp-content/uploads/2012/07/Wireless-Relays-Arduino-Shield-01.jpg)
Wireless NRF24 Controlled Relays Arduino Shield
GPS:, Use GPS module Ublox Neo-7M, or NEO-6M or ATGM332 compatible GPS module. All have the same performace., Fast and high speed locating., By
![](https://s5.electrodragon.com/wp-content/uploads/2018/01/RPI_GPS_LORA-04-768x576.jpg)
GPS SD RF Lora Shield for Raspberry Pi R2 (w/o Lora Module)
![](https://s5.electrodragon.com/wp-content/uploads/2023/12/ESP32-S3-Development-Board-Dual-USB-Wifi-BLE5-scaled.jpg)
WIFI Archives - ElectroDragon
![](https://wiki1.dragino.com/images/thumb/4/4e/Lora_Shield_with_Leonado.jpg/500px-Lora_Shield_with_Leonado.jpg)
Lora Shield - Wiki for Dragino Project
Features, ESP-WROOM-02 is a low-power 32-bit MCU Wi-Fi module, based on the ESP8266 chip. TCP/IP network stacks, 10-bit ADC, and
![](https://s5.electrodragon.com/wp-content/uploads/2018/01/2023-11-28_165738.png)
WROOM-02 WIFI Module, ESP8266, 4MB [D/U]
![](https://i5.walmartimages.com/seo/915-MHz-LoRa-ESP32-OLED-V2-Module-SX1276-IOT-Development-Board-915MHz-LoRa-Antenna-for-Arduino-Smart-Home_334a5698-568a-4f12-a4f8-40c2ab8a4c1f.34e1d07c43216089bcacd64277bc100d.jpeg?odnHeight=768&odnWidth=768&odnBg=FFFFFF)
915 MHz LoRa ESP32 OLED V2 Module SX1276 IOT Development Board +
![](https://how2electronics.com/wp-content/uploads/2019/12/LoRa-SX1278.jpg)
LoRa SX1278 & ESP8266 Transmitter Receiver with DHT11 Sensor
![](https://wiki1.dragino.com/images/thumb/f/f3/LoRa_Shield_Pin_Mapping.png/800px-LoRa_Shield_Pin_Mapping.png)
Lora Shield - Wiki for Dragino Project
GPS:, Use GPS module Ublox Neo-7M, or NEO-6M or ATGM332 compatible GPS module. All have the same performace., Fast and high speed locating., By
![](https://s5.electrodragon.com/wp-content/uploads/2018/01/RPI_GPS_LORA-01-768x571.jpg)
GPS SD RF Lora Shield for Raspberry Pi R2 (w/o Lora Module)