Pi+® (PiPlus®) 1PC PC 10 Port 4 Pin Fan Hub 10-Way 4-pin IDE Fan Speed
About the product: Expand 4-pin fan interfaces, solving the problem of lack of motherboard fan interfaces. Designed for 12V 4-Pin 3-Pin fans, support simultaneous starting at most 10 channel fans. In the hub interfaces, the RED CPU interface is the CPU fan dedicated interface (with speed detection function). Since the
About the product:
- Expand 4-pin fan interfaces, solving the problem of lack of motherboard fan interfaces. Designed for 12V 4-Pin 3-Pin fans, support simultaneous starting at most 10 channel fans.
- In the hub interfaces, the RED CPU interface is the CPU fan dedicated interface (with speed detection function). Since the mainboard can only receive one rotation speed signal, the remaining nine conventional fan interfaces have the PWM function, but no speed signal.
- For both 4-Pin and 3-Pin fans. Please note 4Pin fan speed can be adjusted by temperature control. 3Pin fan can also be used, but because 3Pin has no PWM function, it is at fixed speed after inserting.
- There is EVA double-sided adhesive at the back of the hub, which can be easily affixed to a flat place. Also a fixing screw hole in the middle of the PCB to facilitate fixing to a part of the chassis.
- RED is expected to be a pass through for the CPU fan. So, the hub has a power source fed from the computer power supply, then the speed is regulated by the speed for the source fan. You can connect to the CPU fan lead on the system board or the chassis fan lead. The ten fans will spin at the same speed, that designated by the system for that fan. If the chassis fan is configured in BIOS to run at 50%, you will have 10 fans at 50%.
-
Package content: 1 x 12V 10 way 4-pin ide fan governor, 1x PWM connecting cable.
Description:
- Fan interface: IDE interface, support 3/4 pin
- Product size: 7*4.6cm/2.7*in
- Rated voltage: 12V
- Product model: temperature control 4-pin hub
- Scope of application: motherboard 4-pin interface
- PWM cable length: 40cm/15.7in
- 7.PWM is connected to the motherboard FAN CPU interface through the PWM CONNECTION cable,
- 8. The red interface is the specific interface of the CPU fan, and the black interface is the standard PWM fan interface.
- 9. There is a double-sided EVA adhesive on the back, which can fix the hub in the computer case.
Note:
- 1. The red port must be plugged into a fan first. Pull one end of the PWM cable and plug it into the CPU_FAN interface on the motherboard.
Power up to 10 PC fans from a Single 4-Pin Motherboard PWM Fan Header, In the hub interfaces, the White interface of FAN1 is the CPU fan dedicated
10-Port PWM Fan Hub, Splitter for 4-Pin & 3-Pin Fans
PC 1 to 10 4 Pin PWM Cooler Fan HUB Splitter Speed Controller 12V
EN-Labs 4pin Fan PWM Fan Hub,10 Ports 4 Pin TX4 Hub Splitter
(2 Pack) Toptekits Chassis Fan Hub CPU Cooling HUB 10
Excellent 4-pin PWM 1 to 5 splitter fan power supply extension cable for PC computer motherboard fans, make you easier diy PC computer case. Widely
ThreeBulls PWM Fan Hub , PC CPU Cooling 4 PIN/3PIN Power Cable Hub Splitter Adapter Sleeved Case for 12V Desktop Computer Cooler Fans 1 to 5 Way (15.7
EnLabs PWMHUB10S 10 Ports 4-Pin PWM Fan Hub, SATA 15pin to 10 Fan
NOYITO 10-Channel PC Fan PWM HUB SATA Port
EN-Labs PC Case PWM 4 Pin Fan Hub, 1 to 10 4Pin/3Pin Chassis
EN-Labs 4pin Fan PWM Fan Hub,10 Ports 4 Pin TX4 Hub Splitter Controller Powered by SATA for Chassis CPU Cooler,PC Mining - 1.64FT RPM & PWM controller
